PM850 / 850si / 852si
 
 
PM850 Datasheet.pdf

Print Modes
Fast Draft: 530 cps
Draft: 400 cps
Fast Draft/High Impact: 250 cps
High Impact: 200 cps
Letter Quality: 100 cps
Optical Quality: 65 cps
Graphics: 5,000 dps
Character Matrix
Fast Draft: 9 x 9 cell
Draft: 12 x 9 cell
Letter Quality: 24 x 18 cell
Optical Quality: 36 x 18 cell
Printhead
18 wire parallel array.

Printhead Adjustment
Automatic gap adjustment is standard.

Character Sets
Fast Draft, Draft and Letter Quality for Epson™ and IBM® Proprinter. Optical Quality for OCR-A and OCR-B.

Character Spacing
5, 6, 6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1 and 20 cpi.

Line Length
85 characters at 10 cpi. Also software programmable.

Line Spacing
6 and 8 lpi.

Paper Handling

Zero Tear-Off distance; paper out/paper jam detection; fanfold, continuous forms, edge punched.

Continuous Mode
Automatically loads paper from another tractor if paper out condition occurs. Only available in model 852si.

Operator Controls
Normal Operating Mode: Online, Form Feed/Load and Form Select/Unload.

Form Parameters
Non-volatile memory for ten forms, each supporting settings for: tractor path, cpi, lpi, form length, left and right margins, top and bottom margins, unidirectional printing, slashed or non-slashed zero, language, font, high-impact on/off, form name.

Ribbon
Cartridge: nylon fabric, mobious loop, approximately 15 million characters.

Operating Indicators
LED indicates Online/Fault/Setup; 2 x 16 LCD for form selection; on/off line status and error descriptions.

Power Requirements
Voltage: 100 to 250 VAC ±10%
Frequency: 50 to 60 Hz
Power Consumption: 18W non-printing, 60W printing.

Paper Slew Rate
Model 850/850si: 6 ips rear feed
Model 852si: up to 12 ips bottom feed

Paper Width
2.5 to 9.75 inches (6.4 to 24.8 cm).
 

Paper Loading
Model 850/850si: Rear feed.
Model 852si: Rear feed and straight through bottom feed.

Multi-Part Forms
Model 850: 1 to 5 parts; 0.025" max. thickness
Model 850si/852si: 1 to 9 parts; 0.025" max. thickness
 

Graphics Density
60 to 240 dpi horizontally x 72 dpi vertically.

Audible Noise (Draft Mode)
60 dBA.

Setup (Automatic Methods)
Control panel, pluggable cloning module or remote via Windows program.

I/O Buffer
32k.

Standard Interfaces
Parallel: Centronics compatible.
Serial: RS232, 300 to 9,600 baud.
 

Optional Interfaces
Ethernet.

Software Controls
Emulation choice of Printek, Epson FX¨, IBM Proprinter, DEC LA120/210, Genicom ANSI (includes 20 popular bar codes) or Basic Bar Codes (includes Code 39, 2 of 5, Interleaved 2 of 5).

Physical Specifications
H x W x D: 7"x 18.5"x 17"
(17.8 cm x 47 cm x 43.2 cm)
Second tractor on model 852si adds 3.5" (8.9cm) to height.

Weight: 32 lbs. (16.9 kg)
Second tractor on model 852si
adds 10 lbs. (5.3 kg) to the weight.

Reliability
Model 850: MTBF - 10,000 hours on electronics, with 50% duty cycle.
Model 850si/852si: MTBF - 10,000 hours on electronics, with 100% duty cycle.
Printhead Life: 500 million characters.
Warranty: One-year printer warranty, two-year limited printhead warranty when Printek brand ribbons are used; one-year warranty when non-Printek brand ribbons are used.


* Note: If you plan to do continuous feed print jobs with any of the PrintMaster 850 Series printers, we recommend that you purchase the optional Paper Guide .

 Known Crosses:

 Status:

 
 
PM852 Datasheet.pdf

Print Modes
Fast Draft: 530 cps
Draft: 400 cps
Fast Draft/High Impact: 250 cps
High Impact: 200 cps
Letter Quality: 100 cps
Optical Quality: 65 cps
Graphics: 5,000 dps
Character Matrix
Fast Draft: 9 x 9 cell
Draft: 12 x 9 cell
Letter Quality: 24 x 18 cell
Optical Quality: 36 x 18 cell
Printhead
18 wire parallel array.

Printhead Adjustment
Automatic gap adjustment is standard.

Character Sets
Fast Draft, Draft and Letter Quality for Epson™ and IBM® Proprinter. Optical Quality for OCR-A and OCR-B.

Character Spacing
5, 6, 6.7, 7.5, 8.4, 8.6, 10, 12, 13.3, 15, 16.7, 17.1 and 20 cpi.

Line Length
85 characters at 10 cpi. Also software programmable.

Line Spacing
6 and 8 lpi.

Paper Handling

Zero Tear-Off distance; paper out/paper jam detection; fanfold, continuous forms, edge punched.

Continuous Mode
Automatically loads paper from another tractor if paper out condition occurs. Only available in model 852si.

Operator Controls
Normal Operating Mode: Online, Form Feed/Load and Form Select/Unload.

Form Parameters
Non-volatile memory for ten forms, each supporting settings for: tractor path, cpi, lpi, form length, left and right margins, top and bottom margins, unidirectional printing, slashed or non-slashed zero, language, font, high-impact on/off, form name.

Ribbon
Cartridge: nylon fabric, mobious loop, approximately 15 million characters.

Operating Indicators
LED indicates Online/Fault/Setup; 2 x 16 LCD for form selection; on/off line status and error descriptions.

Power Requirements
Voltage: 100 to 250 VAC ±10%
Frequency: 50 to 60 Hz
Power Consumption: 18W non-printing, 60W printing.

Paper Slew Rate
Model 850/850si: 6 ips rear feed
Model 852si: up to 12 ips bottom feed

Paper Width
2.5 to 9.75 inches (6.4 to 24.8 cm).
 

Paper Loading
Model 850/850si: Rear feed.
Model 852si: Rear feed and straight through bottom feed.

Multi-Part Forms
Model 850: 1 to 5 parts; 0.025" max. thickness
Model 850si/852si: 1 to 9 parts; 0.025" max. thickness
 

Graphics Density
60 to 240 dpi horizontally x 72 dpi vertically.

Audible Noise (Draft Mode)
60 dBA.

Setup (Automatic Methods)
Control panel, pluggable cloning module or remote via Windows program.

I/O Buffer
32k.

Standard Interfaces
Parallel: Centronics compatible.
Serial: RS232, 300 to 9,600 baud.
 

Optional Interfaces
Ethernet.

Software Controls
Emulation choice of Printek, Epson FX¨, IBM Proprinter, DEC LA120/210, Genicom ANSI (includes 20 popular bar codes) or Basic Bar Codes (includes Code 39, 2 of 5, Interleaved 2 of 5).

Physical Specifications
H x W x D: 7"x 18.5"x 17"
(17.8 cm x 47 cm x 43.2 cm)
Second tractor on model 852si adds 3.5" (8.9cm) to height.

Weight: 32 lbs. (16.9 kg)
Second tractor on model 852si
adds 10 lbs. (5.3 kg) to the weight.

Reliability
Model 850: MTBF - 10,000 hours on electronics, with 50% duty cycle.
Model 850si/852si: MTBF - 10,000 hours on electronics, with 100% duty cycle.
Printhead Life: 500 million characters.
Warranty: One-year printer warranty, two-year limited printhead warranty when Printek brand ribbons are used; one-year warranty when non-Printek brand ribbons are used.


* Note: If you plan to do continuous feed print jobs with any of the PrintMaster 850 Series printers, we recommend that you purchase the optional Paper Guide .

 Known Crosses:

 Status:

 
PowersourceOnline Brokerbin
 

 

 Illustrated Parts Listing

(Illustrated Parts) / (RSPL)  
Parts Listings Ribbons, Consumables and Options

 

 

90899 - PM850 Standard Ribbon

90921 - Indelible Ink